Precision Measuring with Incra Tools
INCRA scores again with its precision steel rules. Select the proper slot or hole, insert a .5mm mechanical pencil or .25mm permanent pen and mark the measurement with dead on accuracy.
Micro fine guide holes and slots at every 1/16", 1/32" and 1/64" scale position instantly locate your sharp pencil or scribe at the exact measurement with zero uncertainty and no eye strain! The Professional T-Rules even offer marking holes every 1/100". This is unmatched in the industry.
A regular Marking Rule. This rule offers Incra's patented marking holes at every 1/16 and /32 inch from 0 to 6 inches. Also available in 150mm metric length with marking holes every .25mm.
6" Imperial $14.95
150mm Metric $15.95
T-bar is easily adjusted for making fast vertical measurements, perpendicular lines and perfectly placed horizontal lines. Available in 6" length with marking holes every 1/16, 1/32 and 1/64 inch, 150mm length with marking holes every full, 1/4, 1/2 and 3/4mm or the Professional Combo T-Rule which combines both imperial and metric marking holes up to 1/100 of an inch and .5mm. The end features 3 vertical inches of marking holes every 1/32 inch. You will never be without the correct measurement with these beauties.
6" Imperial $23.95
150mm Metric $23.95
Pro Combo(Imperial/Metric) $29.95
Incra reinvented the protractor by putting extra long guide slots at every 45˚, 30˚, 22.5˚, 5˚ 1˚ and 0.5˚ interval to plot any angle with ease and absolute accuracy. If you take a few seconds to remove the T-bar you will also have an excellent 6" rule with micro-fine marking holes at every 1/32". Also available in 160mm metric length. Includes a .5mm mechanical pencil.
6" Imperial $35.95
160mm Metric $35.95
Microperm Marking Pen
An ultra fine line, waterproof, permanent ink pen. The .25mm tip fits the holes in the Incra rulers perfectly. Marks on metal, glass, plastic, wood and cellophane. Remove marks with alcohol based cleaner.
All Nylon Forming Pliers
Non marring nylon jaw pliers are a must for manipulating wire, especially colored wire. These sturdy, lightweight (only 1 ounce!), all nylon/glass fiber pliers will fit the bill nicely. Three different styles available.
Flat Nose $13.62
Chain Nose $13.62
Nylon Jaw Forming Pliers
Non marring nylon jaw pliers are a must for manipulating wire, especially colored wire. Not just any nylon jaw will do and ours is a high quality nylon which will not damage delicate wire. Stainless, box-jointed with comfort grips. Available in three styles, two with springs.
Round on Round $9.95
Round on Flat $9.95 Flat on Flat $19.95
Replacement Jaws (1 pair)
Round on Round $1.50
Round on Flat $1.50 Flat on Flat $4.15
Metal Hole Punch Pliers
Our newly designed hole punch pliers will punch niobium or titanium to 20ga and copper or silver as thick as 18ga. With ergonomic handles and tempered replaceable pin, these pliers will save you time and money. 1.25mm pin diameter. The pliers are made of thick carbon steel and come with an extra replaceable pin. Additional pins available in packs of five. Length 5.25" (135mm).
Hole Punch Plier 1.25mm $14.95
1.25mm Pin Kit (5 pcs) $6.95
You'll love the Tube Ringer® - with little effort it will put a beautiful corrugated pattern on metal sheet up to 24ga and wire up to 20ga. The 3" rollers will handle sheet stock up to 2.5" wide and leave the metal nice and smooth. Enhance your artistic efforts with this easy to use economical tool. Light duty, not for cross rolling. Not for titanium. Made in the USA.
Fine domestic tool steel, deep heat treated. All stamps are straight (3.25") with 1mm lettering. Please wear eye protection!
NIOBIUM $17.00 1/8 22KGF $17.00
TITANIUM $17.00 ©(Copyright) $12.00
Wood Dapping Block Set
Ideal for the delicate colored surface on Niobium and Titanium, this all wood set has 8 different sized punches/depressions to meet all your doming needs. Perfect for our Niobium Patterned Discs! Depression block has the 6 smallest depressions on one side and 2 largest on the back side. All contained in a handy stand. Depression sizes: 11mm, 14mm, 17mm, 20mm, 23mm, 25mm, 29mm and 32mm. Punch sizes: 10mm, 13mm, 16mm, 19mm, 22mm, 24mm, 28mm and 31mm.
High Speed Steel burs trim rough ends of wire and rod into smooth rounded ends. Excellent prep for threading wire and rod. Fast and clean! Use Anchor Lube to extend tool life.
Size Each 6+ 12+
Similar to the grocery store variety pot scrubbers, but loaded with sharp abrasives! Their soft, flexible action follows the contours of your work for an even scratch finish. Unlike sandpaper, these pads do not remove metal. 6" x 9" pads.
Earrings using Mighty Masks, Scotch Brite Pads & Nb Reg Loops
Ultra fine silicon carbide $2.38 each
Fine aluminum oxide $2.40 each
Coarse silicon carbide $4.27 each
Micro-Mesh Soft Touch Pads
Handy for doing small jobs and repair projects. Great for removing anodizing on raised surfaces. The foam core provides additional flexibility and conformity, while being easy to hold and operate. Silicon carbide crystals on a resilient layer over cloth back. 2" x 2" pads. Available in 100MX, 120MX, 150MX, 180MX, 240MX, 320MX, 360MX & 400MX. Specify grit size.
Soft Touch Kit, 1 of each of the 8 grits, Save 10%! $10.61 each
Surface Saver Tape
Protect your delicate surfaces when further processing is required such as sanding, forming, drilling, bead blasting, filing, etc. Great for protecting items from scratching during storage and transport. Leaves no residue when removed. Not suitable for use as an anodizing resist. 1.5" wide x 100 yd roll.
This half protected with Surface Saver Tape to protect shine
This half bead blasted after anodizing. Note the crisp line!
A clear viscous polystyrene formula that creates a chemical bond to either porous or non-porous, and even rough surfaces. It remains flexible and is ideally suited for findings. Snip tip dispenses just the right amount. Very long shelf life.
Shipped domestically via UPS ground only.
FOREIGN DELIVERY IS AVAILABLE USING A HAZMAT FREIGHT FORWARDER ONLY. WE CANNOT SHIP DIRECT!
3.7 ounce tube w/2.5" Snip tip $7.52 Extra Snip tips $.50